TMC-02310

Computerized Fully Automatic Bilge Pump

The fully automatic 600 gph pump operates on a computerized cycling system that requires the pump to “turn on” every 15 minutes then “shut off” when water is low and load against impeller is reduced. Power for checking is minimum.

MOTOR :12V / 24V
CAPACITY :600GPH (2274LPH)
AMP DRAW :4A (12V) / 2.5A (24V)
FUSE SIZE :5A (12V) / 3A (24V)
HOSE DIA. :3/4” & 1-1/4” (19 & 32mm)
DELIVERY HEAD :10FT. (3M)
DIMENSION :125.5x120x138.9 mm
(LxWxH) (4.94”x4.73”x5.47”)
PACKING :24pcs/ctn/3.34cuft
WEIGHT :21kgs/ctn
MIN Q’TY :24pcs
Specification
ORDER NO.
503-1906011 12V
503-1906012 24V
Where to buy
Warranty
TMC LIMITED WARRANTY (for Marine Equipment)
Please see the TMC’s limited warranty for marine equipment below. Contact us for more information.

TMC Technology Corp., herein referred to as “TMC”, warrants that its marine equipment (the “Product”) will be free from defects in materials and workmanship for one year from the date TMC ships out the Product to original purchaser (who buys directly from TMC). This limited warranty is not transferable, and only applies to the original purchaser (the “Direct Purchaser”).

Should a defect in workmanship or materials in Products or Parts arise during the one year warranty, TMC will, at its opinion, repair such Products or Parts, or replace them with identical or similar parts. Any replacement product shall be warranted only for the remainder of the original product warranty, and shall not extend the original warranty period.

However, TMC is not responsible for (under this warranty) costs of shipping or transportation of the Products or Parts thereof to or from its facility, as well as costs of labor, dismantling or reinstalling of the Products or Parts. TMC’s liability shall not exceed the purchase price of the Product.

EXCEPTIONS

  1. This warranty does not apply if the Product or Parts has been repaired, altered, misused, modified, mistreated, water-damaged, or if the serial number has been removed, defaced, or changed.
  2. This warranty does not cover normal wear and tear of seals and/or stators, or results of dry-running or if damage occurs due to improper maintenance.
  3. This warranty does not cover damage is caused by misuse, abuse, accident; failure to operate or install Products as specified in owner’s manual; or failure to use the Products accordance with the water conditions specified in the owner’s manual.
  4. This warranty does not cover damage caused by water freezing inside Product.
 

The foregoing Warranty is exclusive of and in lieu of all other warranties whether expressed or implied, including any implied warranty of merchantability or fitness except those implied by law, and then only for the minimum duration thereof.

The furnishing of a repair or replacement part shall constitute the sole remedy of the purchaser and the sole liability of TMC, whether on warranty, contract, or negligence, and in no event will TMC be liable for damages; direct or consequential.

TMC further disclaims any liability for economic loss arising from claims of product failure, negligence, defective design, manufacturing defect, failure to warn and/or instruct, lack of seaworthiness, and any other theory of liability not expressly covered under the terms of this limited warranty.
FAQ
Frequently Asked Questions
Pump will not run or pump stops in a sudden
  • Without power
  • Voltage is too low
  • Abnormal wire connection
  • Abnormal switch connection
  • Blown fuse
  • Stuck/Jammed impeller
Motor runs normally but there’s none or decreased water output
  • Voltage is too low
  • Water level is lower than the impeller
  • Discharge hose is kinked/blocked/air-locked or split/disconnected
  • Discharge route is too high
  • Discharge hose is too long
  • Air remains in the discharge route
  • Blocked bottom strainer
  • Impeller is worn out or damaged
Remark:
  1. Please contact original seller or TMC manufacture for further assistance if above chart will not answer your questions.
  2. For safety purpose, please disconnect power to the pump before servicing the product.